Page History

...

In many of your zones the devices for that zone will have physical controls you can use to adjust the heating, such as the buttons on a Radiator Valve. From the zone setup pages, you can choose whether these buttons should be permitted to affect the heating in the zone, and how they affect the heating. The default setting for a zone is ... check_me

• When manual override is disabled, any button presses on devices will be ignored by the system and the heating will carry out its normal schedule.
• When manual override is enabled, the device can be used to put the zone into override mode without having the use the app. When you enable manual override you also choose the duration of the override from the devices in the zone, and the override temperature you want to use if none is selected on the device. 

You have different levels of override control possible, based on the device you are adjusting:

• On the Room Thermostat (DA-WRT-C) you can set the temperature of the override from the device. To override a zone from the thermostat:
  1. Press the up or down button until the desired temperature is reached. The zone will now override to the set temperature for the duration set on the app. If you stop at this point the system will use the override duration set on the app for this zone.
  2. If you wish to set the duration of the override, press the top button once for each hour you would like the override to last for. The zone will now override to the temperature and duration set on the thermostat. check_me
• <image of DA-WRT-C, buttons highlighted>

• On the Room Thermostat (DA-WRT-B) you can set the temperature of the override from the device. To override a zone from the thermostat:
  1. Rotate the dial until the desired temperature is reached. The zone will override to the set temperature for the duration set on the app.
• <image of DA-WRT-B, dial highlighted>

• On a Radiator Valve (DA-WRV-C, DA-WRV-B, or DA-WRV-A) you can set the temperature of the override from the device. To override a zone from the Radiator Valve:
  1. Press the up or down button until the desired temperature is reached. The zone will override to the set temperature for the duration set on the app.
• <image of DA-WRV-C, buttons highlighted>

• On the Single Channel Receiver (HO-SCR-C) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. Press the On (top) button. The system will use the override duration and override temperature set on the app for this zone.
• To override a zone OFF from the receiver unit:
  1. Press the Off (middle) button. The system will use the override duration set on the app for this zone and override to the Off setting for this zone type.
• <image of HO-SCR-C, buttons highlighted>

• On the Dual Channel Receiver (HO-DCR-C) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. Check the door panel to see which of the white buttons relates to the zone you have chosen to override.
  2. Press both the correct white button and the green button at the same time. The system will use the override duration and override temperature set on the app for this zone.
• To override a zone OFF from the receiver unit:
  1. Check the door panel to see which of the white buttons relates to the zone you have chosen to override.
  2. Press both the correct white button and the red button at the same time. The system will use the override duration set on the app for this zone and override to the Off setting for this zone type.
• <image of HO-CCR-C, door open, white & green buttons highlighted>

• On the Electric Switch (HO-ESW-D) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. Press the button at the bottom left hand corner of the receiver unit. The system will use the override duration and override temperature set on the app for this zone.
• <image of HO-ESW-D, buttons highlighted>

• On the Smart Plug (PH-PLG-C or PO-PLG-B) you can trigger an from the device. To override a zone ON from the receiver unit:
  1. When the plug is off, press the button in the middle of the plug. The system will use the override duration and override temperature set on the app for this zone.
• To override a zone OFF from the receiver unit:
  1. When the plug is on, press the button in the middle of the plug. The system will use the override duration set on the app for this zone and override to the Off setting for this zone type.
• <image of PH-PLG-C, button highlighted> check_me - all of above

If you have a device in the My House, such as a Receiver unit controlling your heating or a Thermostat reporting the temperature to My House this can be used to affect all of your Radiator and Underfloor rooms with one manual override. 

• For a Single or Dual Channel Receiver you can press the respective on button (as detailed above) and all of your Radiator and Underfloor rooms will override to the temperature and duration set in My House.
• For a Thermostat you can adjust the temperature (as detailed above) and all of your Radiator and Underfloor rooms will override to the seelcted temperature on the device and to the duration set in My House.

For more information on manually overriding devices, see the Override Mode chapter. This setting is shown in all zones types.   check_me

Pre-heating

The Genius Hub can automatically calculate the pre-heat duration for a chosen room, so that the room will reach the set temperature at the start of the ‘heating period’, rather than just starting to heat up at that time. Your Genius Hub is adaptive, so it's always learning from the temperature recorded by each room sensor. Using the local weather data and the heating history for each room, it will constantly adjust the pre-heat duration as the weather changes. This default setting for pre-heating is disabled. check_me

...