The Genius system has been tested with a wide variety of boilers, heat pumps and other heat sources and there are 3 Receiver Units which can be used to control these: the Single Channel Receiver, Dual Channel Receiver and Electric Switch.
| Info |
|---|
Standard wiring diagrams are provided with the system. To download a copy of the wiring diagrams, visit: https://www.geniushub.co.uk/wiring |
The Single Channel and Dual Channel receiver units are rated to 3A maximum. They can only be used to switch a zone valve or a boiler and not a circulation pump. Controlling a circulation pump will result in damaging the receiver unit, voiding the warranty!
| Warning |
|---|
- Do not attempt to wire in your boiler controller if you are not 100% sure that you know what you are doing. Danger of electric shock! All wiring
|
...
- should conform to IEE regulations. The boiler and wiring for the boiler controller must be electrically isolated before you commence work on wiring in the boiler controller!
- To comply with G12 regulations, a hard-wired cylinder stat. must be present on every system to protect against scalding.
|
Combination Boiler (Single Channel Receiver)
Included in the Genius Starter Kit is the Single Channel Receiver, which is most commonly fitted to a Combination boiler (for properties without a hot water tank). In many cases you can swap in the Single Channel Receiver where the wired house thermostat or boiler programmer was located as the Single Channel Receiver uses a standard backplate. You need to ensure that wiring is correct for the Single Channel Receiver before placing it on the backplate.
...
| Info |
|---|
- If there is no existing boiler programmer then the Single Channel Receiver must be wired into the boiler as if it were an external programmer or thermostat. See wiring diagrams provided by the boiler manufacturer to confirm the wiring guides provided with this installation manual.
- If you replace the existing house thermostat with the Single Channel Receiver, and leave the existing boiler programmer (not recommended), the customer must be aware that they will have no control of the boiler if the programmer turns off. The existing programmer in this case must be set to always on or constant to make sure that the Single Channel Receiver retains control of the boiler at all times.
- If you remove the existing wired house thermostat out of the control circuit (recommended), it must also be removed from the control in the boiler wiring centre, otherwise the Single Channel Receiver will not have control over the boiler.
|
...
System Boiler (Dual Channel Receiver)
Included in the Genius Starter Kit + Hot Water On/Off is the Dual Channel Receiver, which is most commonly fitted to a System boiler (for properties with a hot water tank). The existing programmer must be exchanged with the Heat Genius Dual Channel Receiver to control the heating and the hot water. You need to ensure that wiring is correct for the Dual Channel Receiver before placing it on the backplate.
...
| Info |
|---|
- The temperature in a hot water tank will stratify, and so the Electric Switch will measure a different temperature dependent on where on the tank it is located. It is recommended to use the location of the existing Cylinder Stat or a pocket built into the Hot Water tank. For more information, please see the installation manual provided with the hot water tank.
- The existing cylinder stat should be set to a temperature above the temperature required on the app, and above 60º to protect against legionella.
- Using the appropriate wiring, as in accordance with BS7671 (or newer if such exists).
- The Electric Switch is rated to 13A and must not be wired to an immersion heater with a higher rating. This will result in damaging the Electric Switch and voiding the warranty!
|
General Information
...
...
...
| Warning |
|---|
| Do not attempt to wire in your boiler controller if you are not 100% sure that you know what you are doing. Danger of electric shock! All wiring should conform to IEE regulations. The boiler and wiring for the boiler controller must be electrically isolated before you commence work on wiring in the boiler controllerTo comply with G12 regulations, a hard-wired cylinder stat. must be present on every system to protect against scalding. |